Technical Section or How to fix it
+22
DRKNSTRMY
Ben79hz
wizard1
ryno
DD.165
soundman
Moppo
Rusty McCrusty
highwaymenace
pano
shorts
billet
Shagginwagon82
alien8
Big Bunny
mazdragon
Tweaker
CURSED
Mexican
catbug
Admin
shaginwagin
26 posters
Page 11 of 11
Page 11 of 11 • 1, 2, 3 ... 9, 10, 11
Over heating
https://i.servimg.com/u/f85/13/95/47/24/dsc02911.jpg
Holden 202 overheating, any suggestions?
Holden 202 overheating, any suggestions?
Ben79hz- Posts : 66
Join date : 2008-08-19
Location : East coast vanner-Blacktownish
Re: Technical Section or How to fix it
might have something to do with the Jim Bean the engine's been guzzling....
mazdragon- Posts : 1973
Join date : 2008-08-14
Location : somewhere on the planet in my den
Re: Technical Section or How to fix it
atleast it was eletrical. conrod couldve knocker of the altenator
Guest- Guest
Ben79hz- Posts : 66
Join date : 2008-08-19
Location : East coast vanner-Blacktownish
mazdragon- Posts : 1973
Join date : 2008-08-14
Location : somewhere on the planet in my den
Re: Technical Section or How to fix it
You done well Gwasshoppa!
You suxessfoolly compreet lessan numa wahn!
Now you weddy for Lessan numa whoo.
The indaside hof Phan!
you needi subtitle? Fif dowa, typie wong time!!!!
You suxessfoolly compreet lessan numa wahn!
Now you weddy for Lessan numa whoo.
The indaside hof Phan!
you needi subtitle? Fif dowa, typie wong time!!!!
Vannin- Posts : 567
Join date : 2009-05-08
Age : 54
Location : Noble Park North (SE Melbourne) WASTELANDS VANNER
Re: Technical Section or How to fix it
nah, itza hokai, gotja fewst tyme
mazdragon- Posts : 1973
Join date : 2008-08-14
Location : somewhere on the planet in my den
Re: Technical Section or How to fix it
Well done ( i dont talk Kung Foo ) if ya do vour van this good crash test dummies will be out of a job..
Re: Technical Section or How to fix it
thanks, i'm proud of it cos i did it alllll by myself. i just hope i don't stuff the van up.... i'll keep it simple for starters i think.
mazdragon- Posts : 1973
Join date : 2008-08-14
Location : somewhere on the planet in my den
Re: Technical Section or How to fix it
I may have posted before but thought it wouldn't hurt to put here again...
soundman- Posts : 316
Join date : 2008-10-23
Location : The Driver's seat... or in the rear.
Re: Technical Section or How to fix it
and for those who can't mark out, cut straight or don't want to attempt it.
Shout out to WKDVAN, Wicked or Murray, he can get them CNC Cut to size with any opening shape required at a extremely reasonable price.............
Shout out to WKDVAN, Wicked or Murray, he can get them CNC Cut to size with any opening shape required at a extremely reasonable price.............
Vannin- Posts : 567
Join date : 2009-05-08
Age : 54
Location : Noble Park North (SE Melbourne) WASTELANDS VANNER
Re: Technical Section or How to fix it
i was just looking at my copy of that template last night thinking i should post it up.. but you done it for me. Thanks.
i have been locking for my old roof console template but cant find it anywhere.
i have been locking for my old roof console template but cant find it anywhere.
Re: Technical Section or How to fix it
plus you wouldn't have to figure out what all those old people measurements actually mean
soundman- Posts : 316
Join date : 2008-10-23
Location : The Driver's seat... or in the rear.
Re: Technical Section or How to fix it
thanks.. so i'm old enough to remember.. i have people laugh at me when i do plans these days as 1/2 the messurements are in inches and the other in metric.
Re: Technical Section or How to fix it
very nice job maz. good to see your planning to send more time in the shed ironing also
Guest- Guest
Re: Technical Section or How to fix it
welldone Maz thats the best & largest ironing bench l seen in a longtime
Re: Technical Section or How to fix it
how did i know i was going to get comments re the iron?? to let you guys know, I had to cut the bench top, it was a 2.5m laminated bench top they were going to throw out at work (the kind you get in an office as a desk etc.) I had to cut it to make it fit and used the balance for the short part of the L shape. So the moisture doesn't get in, i bought the iron on laminate edging, hence the iron in the shed.... but yeah, you're right, one hell of a ironing board.....
mazdragon- Posts : 1973
Join date : 2008-08-14
Location : somewhere on the planet in my den
Re: Technical Section or How to fix it
Thats great, Shows my age, i understand the measurements.
Anyone got one for the XD-XF? my young blokes tying to make an arch for his van.
Anyone got one for the XD-XF? my young blokes tying to make an arch for his van.
Ramble- Posts : 566
Join date : 2009-02-23
Location : mid nth coast nsw
Re: Technical Section or How to fix it
found this interesting, not sure if its on here somewhere
http://www.tchc48-78.com/speedocalc.html
http://www.tchc48-78.com/speedocalc.html
CURSED- Posts : 238
Join date : 2008-08-15
Location : NSW vanner- mt druitt
Re: Technical Section or How to fix it
rambletamble wrote:Thats great, Shows my age, i understand the measurements.
Anyone got one for the XD-XF? my young blokes tying to make an arch for his van.
I made a coreflute template for my XF, just went to look for it and not sure where it's gone......
Will look tomorrow in the day light..............
Vannin- Posts : 567
Join date : 2009-05-08
Age : 54
Location : Noble Park North (SE Melbourne) WASTELANDS VANNER
Page 11 of 11 • 1, 2, 3 ... 9, 10, 11
Page 11 of 11
Permissions in this forum:
You cannot reply to topics in this forum
9/2/2016, 1:20 pm by Moorza
» Squaw in the modern age of Vanning
9/2/2016, 1:15 pm by Moorza
» Fire Truck roof spoiler
6/11/2014, 10:22 am by VANTOM
» CAR SHOW AT BOWRAL NSW
25/10/2014, 4:45 am by VANTOM
» A van only magazine needed? Are you interested?
1/9/2014, 9:31 am by vanner065
» October 19th
14/8/2014, 3:44 pm by petrolhead
» Fathers Day Hot Rod Show 2014
13/8/2014, 2:13 pm by petrolhead
» hsv front to a HJ
26/7/2014, 7:02 am by chrisHQvan
» REGO PLATES
1/7/2014, 2:18 pm by petrolhead